TUCHENG GLASS TECHNOLOGY CO.,LTD

Locality：First Page>>>Float Glass Equipment>>>Stacking Machine >>>Horizontal Stacking Machine for Glass Medium and small sizes

Brief Introduction to Stacking Machine for Glass with Medium and Jumbo Size:

  • Technical Specification

  1. Working stations of the stacking machine: 2 Nos.
  2. Max. weight of single glass sheet: 0.9 t
  3. Max. stacking thickness: 400mm
  4. Range of glass specification for stacking:（the effective area of the standard suckers when out of the factory:2.90 m×1.90 m）
    *3 mm glass: 3.5m×2.5m ≥ Specification
    *4 mm glass: 3.5m×4m ≥ Specification
    *5 mm glass: 3.5m×4.5m ≥ Specification ≥3m×2m
    *6 mm glass: 3.5m×5m ≥ Specification
    *8 mm glass以上: 4m×6m ≥ Specification
  5. Stacking cycle with medium size of glass (including paper laying)：13s～20s. （the cycle time can be adjusted subject to the glass while two sets of stacking machines working simultaneously,it can meet the requirement for stacking glass with minimum size).
  6. Positioning accuracy at glass running direction of the main roller conveyer：±2mm
  7. Detecting accuracy for glass offset the central line of the main roller conveyer ：±2mm
  8. General positioning accuracy for stacking： 5mm
  9. Max. running speed with sucker carriage： 2m/s
  10. Max. elevating distance with sucker carriage： 410 mm
  11. Max. elevating speed with sucker carriage： 300 mm/s
  12. Height positioning accuracy with sucker carriage： ±3mm
  13. Max. turning & lifting weight for glass with the stacking carriage：5 t
  14. Max. turning & lifting angle with the stacking carriage： 85°
  15. Max. running distance with stacking carriage： 4m
  16. Positioning accuracy of the stacking carriage running： ±5mm
  17. Effective contacting area between the stacking carriage and glass：2.8m×2.8m
  18. Max. running speed with the stacking carriage： 500mm/s
  19. Pressure of compressed air required： ≥5Kg/cm2 Interface of G3/4"（to be provided by the customer）
  20. Flow rate of vacuum pump： 0.6M3/min
  21. Electricity： 380V 10KW

  • Main Features

  1. Design of truss frame wiht stacking machine running enables the operator to operate freely with easy loading and safe operation.
  2. Because of fully use of servo motor, the sucker running and elevating are motion dirigibility and precise positioning.
  3. Due to a small pressure applied to the glass by the elevating system, stacking of the thinner glass is possible and reliable.
  4. There is very little running noise because of Nylon wheel of high hardness with the sucker carriage.
  5. The moving transmission is by means of imported wire tooth belt of high strength without lubricant and no noise.
  6. It can automatically modify the error of deviation with the central line caused by the offset of glass of main line by combining glass edge detecting device.
  7. Automatically detect the glass specification so as to determine the locations of both stacking carriage and flapper accordingly.
  8. The operation of the equipment is reliable in a long term owing to imported high flexible cable and ring backstay.
  9. The sucker automatically fetches the paper. This enables the manual auxiliary paper laying more safe and reliable.
  10. Apart from the steelwork is by means of spray-paint, all the structure is by means of treatment of spray-plastic, so the apparent of the equipment is in harmony.
  11. The movable stacking carrier makes the way of stacking more dirigibility.
  12. The failure warning is by means of phonetic panalarm and there are alarming type displayed on the interface of man-machine.
  13. Analogue display of working states and parameters modification for the stacking machine at the man-machine interface.
  14. The possible and unexpected situations during operation have been fully considered in the designed software, the corredponding program for remedy has also been prepared so as to ensure saftety of both equipment and the operators.
  15. It is very easy to connect with the control system of the main line, the machine itself is also installed with specification detecting device providing a serial interface for communication and sending parameters like glass specification and grade etc.
  16. The electrical control system are all imported components.
  17. All the pneumatic components are of Japanese SMC products.

　

Copyright：Qinhuangdao Tucheng Glass Technology Co., Ltd.

Made by：Qinhuangdao Tucheng Glass Technology Co., Ltd.

: tucheng@tucheng.com

Optimum browser：IE4.0 or above with resolution of 800×600